tag:blogger.com,1999:blog-24415034.post3745374570042942779..comments2024-03-18T10:19:55.782-04:00Comments on The Velo ORANGE Blog: Converting From 26" to 650bVelo Orangehttp://www.blogger.com/profile/02835615331417822722noreply@blogger.comBlogger37125tag:blogger.com,1999:blog-24415034.post-68500096342481160082016-01-11T14:49:20.669-05:002016-01-11T14:49:20.669-05:00I'm currently running my Long haul Trucker (26...I'm currently running my Long haul Trucker (26") with 650b x 41 Surly Knards. Plenty of room for my wooden fenders still.<br /><br />Differences I've noticed are a lower-trail ride that is a bit snappier than the standard LHT ride. The front wheel has more flop with weight now than before. My second nature habit of throwing my left leg over the seat has been a bit of a challenge, leading to a couple almost-topples.Andyhttps://www.blogger.com/profile/04136973520072250066noreply@blogger.comtag:blogger.com,1999:blog-24415034.post-54162416964376888502015-07-07T11:01:15.386-04:002015-07-07T11:01:15.386-04:00Thanks big for your help with the brake selection....Thanks big for your help with the brake selection. the Promax v-brakes are far cheaper than the brakes I was looking at!Anonymousnoreply@blogger.comtag:blogger.com,1999:blog-24415034.post-23672964822163153552014-12-08T14:11:12.282-05:002014-12-08T14:11:12.282-05:00I know this is an old thread, but in case anyone s...I know this is an old thread, but in case anyone stumbles upon it looking for answers: There are now two pretty cheap options for getting either 26" or 700C cantis studs to work for 650B. Check out Elevn Technologies brake adaptor.....its intended for BMX converions but is basically an aluminum tab the mounts onto the canti boss using the holes left when you screw out the stud. An additional pin fits into the old spring hole for extra stability. It then has an additional offset hole to screw the canti stud in. The adaptor could be mounted right side up or upside down to raise or lower the stud height by 16mm. Also check out Promax P-1 Linear V-brakes.These are cheap and have 35mm of pad adjustment. They also come in 108mm or 85mm arm length so there are options for both mtb and road levers. Hopes this helps someone trying to do a conversion.Anonymousnoreply@blogger.comtag:blogger.com,1999:blog-24415034.post-55597329090931375192014-04-03T22:43:49.923-04:002014-04-03T22:43:49.923-04:00Hey. I was the last poster here a few years ago. I...Hey. I was the last poster here a few years ago. I'm still curious about this, I still haven't seen evidence of making canti's on a 26" bike work around a 650b rim. I tried about 4 pairs of canti's and a v brake just to be sure. And the difference is even greater when trying to convert from 700c to 650b. I dont see how y'all are pulling this off!<br />BiscuitsAndGravelhttps://www.blogger.com/profile/04376293203644390309noreply@blogger.comtag:blogger.com,1999:blog-24415034.post-70462929553125753162012-12-07T18:30:17.963-05:002012-12-07T18:30:17.963-05:00I've been working on converting a Bridgestone ...I've been working on converting a Bridgestone mb3 to a touring bike with 650b wheels. I finally got everything together and when I put the wheels in the frame I realized that the brakes pads will not line up with the rim, even at the top of their adjustment. I'm using the Tektro 720's on a rigid mtb fork, they don't line up with the front, or the rear rim. I'm pretty bummed to see this, I'd been assuming I could make this work. Any suggestions for other canti brakes I can use?<br />Thanks.Anonymousnoreply@blogger.comtag:blogger.com,1999:blog-24415034.post-65764339512864978382012-08-06T11:49:57.720-04:002012-08-06T11:49:57.720-04:00Thanks everyone for your commentsThanks everyone for your commentsOptimistic Travellerhttps://www.blogger.com/profile/00627326417309672131noreply@blogger.comtag:blogger.com,1999:blog-24415034.post-39898759818210490232012-08-06T11:33:12.674-04:002012-08-06T11:33:12.674-04:00Optimistic traveller
This is a good link for info...Optimistic traveller<br /><br />This is a good link for info about braze on distances<br />http://bikebuilding.blogspot.com/2006/12/braze-on-distances-index.html<br />I don't know if it would work or not. The Zeste brakes have a lot of travel, but I'm not sure they would have enough to go from 26" to 700CAnonymousnoreply@blogger.comtag:blogger.com,1999:blog-24415034.post-9820154230449262322012-08-04T13:46:57.780-04:002012-08-04T13:46:57.780-04:00Maybe this has been answered, but its hard to tell...Maybe this has been answered, but its hard to tell. Could the Gran Cru cover the range from 26 inch to 700C or is that too big. <br /><br />Or, since I am building a new frame can the cantilever brake bosses be brazed in such a way that the Gran Cru, or any other canti brake cover the range from 26 inch through 650B to 700C? <br /><br />I'm building a travel frame and while at home I would like to use a 700C wheelset, travelling with 650B or 26inch would make for a smaller, lighter travel package/burden.Optimistic Travellerhttps://www.blogger.com/profile/00627326417309672131noreply@blogger.comtag:blogger.com,1999:blog-24415034.post-50203002289203216752012-05-09T22:29:35.739-04:002012-05-09T22:29:35.739-04:00Great info. With the new Disc Trucker, brake adjus...Great info. With the new Disc Trucker, brake adjustment becomes irrelevant. For those who have done this with a 26" Trucker (either kind), what is the max 650b tire size you can run and still use fenders? Ideally I'd be looking at a 650b x 38 or so with VO hammered fenders. Will it work?<br /><br />KevinKevinhttps://www.blogger.com/profile/06069565695802769138noreply@blogger.comtag:blogger.com,1999:blog-24415034.post-25854890659687083132011-12-19T21:52:32.895-05:002011-12-19T21:52:32.895-05:00Thanks for all the information here. I have severa...Thanks for all the information here. I have several older bikes laying around and after reading some of the stuff here i finally have the nerve to do some customizing@Kellyhttp://rims-andtires.comnoreply@blogger.comtag:blogger.com,1999:blog-24415034.post-86421685080197522942011-06-06T11:46:49.198-04:002011-06-06T11:46:49.198-04:00Big Apples are good rugged commuter tires, perfect...Big Apples are good rugged commuter tires, perfect if you ride through broken glass and potholes. Pari-Motos offer a ride that is an order of magnitude better; they literally transform a bike. To some the cost is a deal-killer, to others it's worthwhile.Le Cagotnoreply@blogger.comtag:blogger.com,1999:blog-24415034.post-52784117349489451762011-06-04T10:39:55.934-04:002011-06-04T10:39:55.934-04:00The Schwalbe Big Apple liteskin published weight i...The Schwalbe Big Apple liteskin published weight is 600g and mine weighed in at 580g (yes I weighed them :)). Granted that is still almost twice as heavy but they have a reflective side wall and a side wall for a dynamo bottle. In addition, they have fantastic tread and are virtually puncture proof. The latter feature is something I highly regard for a city/commuter tire. Furthermore, I seriously question whether you'll enjoy the minuscule improvement in ride quality (if any) after you spent additional money on rims, spokes, brakes, and labor to convert from a perfectly capable 26" (and stronger) wheel. If you do think the ride is better it will only be perceived improvement to justify the unnecessary expense.Anonymousnoreply@blogger.comtag:blogger.com,1999:blog-24415034.post-35810120221385159522011-06-01T12:22:15.839-04:002011-06-01T12:22:15.839-04:00I don't think that Schwalbe 50mm Big Apples ar...I don't think that Schwalbe 50mm Big Apples are comparable to Pari-Motos. They weigh 700-800g, depending on who you believe, versus 280g for the Pari Motos. And the Big Apple's ride is not even close to being as nice. The reason for conversion is that there are no 26" tires that are as good as the better 650b tires.Le Cagotnoreply@blogger.comtag:blogger.com,1999:blog-24415034.post-75428762013293066952011-05-31T14:26:37.979-04:002011-05-31T14:26:37.979-04:00I understand the 700c to 650b conversion but 26&qu...I understand the 700c to 650b conversion but 26" to 650b isn't quite as logical. What you gain by increasing rim diameter (which isn't much) you lose in tire selection. You go from thousands of tire choices to maybe a dozen. I have an '84 Stumpjumper and I did consider swapping out the 26's for 650b's but instead I decided to buy Schwalbe's 2" (50mm) Big Apples. Got all the benefits (cushy ride, low rolling resistance, etc) for less money.Anonymousnoreply@blogger.comtag:blogger.com,1999:blog-24415034.post-46388785378174759152011-05-24T17:43:54.622-04:002011-05-24T17:43:54.622-04:00Someone did, Stan's ZTR 355 650b are listed at...Someone did, Stan's ZTR 355 650b are listed at 385g. Also listed as "out of production".Fred Zeppelinnoreply@blogger.comtag:blogger.com,1999:blog-24415034.post-44080984235342455652011-05-23T19:46:44.094-04:002011-05-23T19:46:44.094-04:00The Catch-22 of the 559 to 584 conversion is that ...The Catch-22 of the 559 to 584 conversion is that while there are some really nice 650b tires available, all of the available rims are pretty stout.<br /><br />There are quite a few MTB rims in the 400g range, but every 650b I've seen is up around 500g. So going to 650b gets you get some nice, light, puffy tires, but mounted on heavy rims.<br /><br />Granted, for loaded touring or a commuter bike, you WANT those sturdy rims, but if 400g 26er's work fine for you, then why can't someone make a 418g (400 X 584/559) 650b'er?Anonymousnoreply@blogger.comtag:blogger.com,1999:blog-24415034.post-70973068754347142011-05-23T13:50:15.223-04:002011-05-23T13:50:15.223-04:00In my experience with frame design, I am far more ...In my experience with frame design, I am far more on the side of wheel diameter corresponding with tire width. The effective difference between wheel diameters as demonstrated by this post is far too minuscule for any rider to notice a difference in the geometry. For conversions, I would agree it is important to consider bottom bracket drop. For most road frame that have clearance for 28s max, pedal strike is rarely an issue since bottom brackets are far too high these days. I've based all these points on my own 7OOc to 65Ob conversion; which is a 65cm c-t-c. I am also brazing a 68cm frame designed around Grand Bois Hetres. Though 7OOc has a wider array of tire choices, 65Ob presents a few very high quality tires worth the investment. Perhaps if Grand Bois or Challenge made a 7OOc tire over 32mm wide, I'd revisit the possibility, but I'd say even taller riders have a fair amount to gain from a 65Ob conversion with very little to loose.<br /><br />As far as looks go, when we start talking about frames bigger than 62cm, they will always look a bit silly and disproportionate. It ain't the bike, it's the ride.Christopher Grandehttps://www.blogger.com/profile/10976363457933306408noreply@blogger.comtag:blogger.com,1999:blog-24415034.post-8814366054147097032011-05-23T13:45:55.879-04:002011-05-23T13:45:55.879-04:00Nice to see you're working at VO now, Nick. 2n...Nice to see you're working at VO now, Nick. 2nd Cycle misses your extensive bike knowledge! Keep the posts coming, maybe I'll see you on the road someday.Kylehttps://www.blogger.com/profile/09384846006746810012noreply@blogger.comtag:blogger.com,1999:blog-24415034.post-59717920006167618082011-05-23T12:40:34.664-04:002011-05-23T12:40:34.664-04:00James --
Many cantilever brakes can go from 27...James --<br /><br />Many cantilever brakes can go from 27' to 700c. My favorite is the Shimano XT M732 wide-profile canti. It easily has enough adjustment. It is also a great brake.doug in seattlenoreply@blogger.comtag:blogger.com,1999:blog-24415034.post-14584556378575598112011-05-23T01:44:35.555-04:002011-05-23T01:44:35.555-04:00My 1985 Trek 720 didn't need new brakes when I...My 1985 Trek 720 didn't need new brakes when I converted it from 27" to 700c.<br /><br />650Bs aren't for us tall guys: Larger frames (61cm+) that were built for 700s look comical with 650Bs mounted. If the appearance doesn't deter you, you will likely need new brakes,and you'll probably be scraping pedals, at least occasionally.<br /><br />I remain happy with my 700c wheels.Robert Linthicumhttps://www.blogger.com/profile/04309652843831858990noreply@blogger.comtag:blogger.com,1999:blog-24415034.post-60942796892812946712011-05-22T02:37:30.501-04:002011-05-22T02:37:30.501-04:00David (and others interested in A/B/C/(and the sup...David (and others interested in A/B/C/(and the super elusive D) wheel sizes.<br /><br />It is my theory that wheel sizes used to fit into three families.<br /><br />700 (for tall people) (sometimes labeled as 28")<br />650 (for short/medium people) (sometimes labeled as 26")<br />600 (for children) (sometimes labeled as 24")<br /><br />The outer edge of the tire diameter would be the same for the A B and C sizes, the larger rim having the smallest tire and the smallest rim having the largest tire. Possibly all intended to fit the same bike? You could have three wheel sets for each bike depending on what you were doing?<br /><br />The A rim would be the largest diameter and would take a narrow tire (appx 1 1/4"-1 3/8"). Intended for the smoothest roads/paths.<br /><br />The B rim would be a smaller diameter and would take a medium width tire (appx 1 1/2"). Intended for urban/cobblestone riding.<br /><br />The C rim would be smallest (strongest) and would take a wide tire (appx 1 3/4"). Intended for racing.<br /><br />Since the early (non-velodrome) races were on what would've been extremely rough, rutted, unpaved roads, you would need those small rims/wide tires. As road conditions improved over the 20th century, racers were able to get by with narrower tires. Tall road racers continued to use 700C rims, the shortest continued to use 650C. Instead of using wide tires, they downsized to a ridiculous sub 1" tire.<br /><br />The 700a and 700b are long gone (until recently they were still possible to source from a few wholesalers, but I haven't seen any in a long time). Wide 700c (622) tires are back in 29"er form, but generally wider than 1 3/4.<br /><br />700d (587) was a super short lived model, even smaller than 700c (putting it between 650a and 650b, but with a wider tire. Appeared on an 80's ATB, by Giant?<br /><br />650a (590) is the 26x1 3/8 size common on many British 3 speeds. Intended for modern urban pavement.<br /><br />650b (584) is the size on many randonneur/porteur bikes intended to be ridden on mixed road conditions.<br /><br />650c (571) used on small road bikes with sub 1" tires and Schwinn heavy-weight bikes with 1 3/4" tires.<br /><br /><br />Anyone have evidence to support(or destroy) my theory?Natehttps://www.blogger.com/profile/00500769861450004284noreply@blogger.comtag:blogger.com,1999:blog-24415034.post-12500087428938544862011-05-22T00:19:17.450-04:002011-05-22T00:19:17.450-04:00Hi. I was wondering about other conversions. I hav...Hi. I was wondering about other conversions. I have a bridgestone 200 mixte that will convert to 650b according to the guidelines posted here: http://www.bikeman.com/content/view/1161/33/ The bridgestone originally had 27" wheels. I noticed in a previous post Chris said he wasn't an advocate of 650b conversions. I'm wondering why he made this comment but I'm pretty sure it's just because there are details in bicycle geometry that work best with 650b wheels. I'm guessing that the fork rake ideally should be calculated to accommodate for the extra cushion of the wider tires. In your opinion which is best to convert to 650b? 27", 700c or 26" wheeled bicycles? Can you discuss some of the specifics of 650b frame geometry?Anonymousnoreply@blogger.comtag:blogger.com,1999:blog-24415034.post-16680207236140870692011-05-21T23:28:47.091-04:002011-05-21T23:28:47.091-04:00The Guth: Nice ride. I have a big place in my he...The Guth: Nice ride. I have a big place in my heart for fat tire drop-bar bikes. Perfect for escaping into the mountains, especially in you neck of the woods.<br /><br />Elsewhere on the net I have seen Tektro Oryx brakes happily mated to 650b rims. Good news for LHT owners with stock brakes.<br /><br />Paul advertizes 60mm of vertical adjustment for the Moto BMX brake, which allows for 26" to 700c conversion, and everything in between. This may be the solution to those that are dedicated to owning one bike (and three wheel sets). Of course a proper v-brake lever would be necessary.<br /><br />James: In my experience, 27" to 700c conversion does not require new brakes. Many 80's touring bike were specced with Dia-Compe cantilevers, many of which are actually the best solution. In addition, smooth post cantilever brake pads like those from Kool Stop have loads of pad material, thus allowing a little uneven pad wear if you cannot get the pad perfectly level. I estimate putting over 6000 miles on a pair of pads salmon Kool Stop pads. They are indefatigable. <br /><br />Three Speed: Some red Hetres would really spice up that Hi-Ten touring machine. I would love the juxtaposition of a steel-body Shimano SIS derailleur backdropped by Hetre tires. Most importantly, does you bike plane?Nicholas Carmannoreply@blogger.comtag:blogger.com,1999:blog-24415034.post-7977921665954539392011-05-21T18:21:48.574-04:002011-05-21T18:21:48.574-04:00Cool, does anyone know if those Tektro brakes work...Cool, does anyone know if those Tektro brakes work for 27" to 700c? Or if not, do the current Grand CRu brakes work? I noticed for the 650b conversion it was vertical movement up, but what about down?<br /><br />jamesjamesnoreply@blogger.comtag:blogger.com,1999:blog-24415034.post-11209011108652137752011-05-21T16:11:40.200-04:002011-05-21T16:11:40.200-04:00I finished building my second frame a couple of mo...I finished building my second frame a couple of months ago. I wanted to use 650b wheels and tires, but designed it to also run 700c if I wasn't happy with my 650b "experiment".<br /><br />Well, in the month and a bit since I got the frame back from the painters, I've ridden my original frame, a 700c bike that I love the ride of, exactly once, and the 650b frame a couple of dozen times. I'm running Panaracer/Riv Fatty Rumpkin's, which roll fast and absorb crappy roads like nothing else. Love 'em. But they're a tough sell to cyclists who don't know 650b (i.e. hard core roadies)<br /><br />The thing that is holding back 650b as a platform, IMO, is the lack of inexpensive rims in the size that would allow a person to build up a basic set of wheels for $150 or so just to try them out. I was fortunate to find a reasonably priced set of wheels built up around 584ERD Weinmann ZAC 19's; these would be a perfect rim for this purpose, as the going price seems to be under $25 each; however, they are next to impossible to find. The next least expensive set of rims is the VO offering, but they are twice the price.Pete Ruckelshaushttps://www.blogger.com/profile/15020408559096296268noreply@blogger.com